Note that the classes that are not used by the TCU firmware is not displayed to simplify the chart. If firmware is developed they will be added.
| Mercury2 Hardware | STD | INT | ADV | ULT | Notes |
| Hardware Inputs | |||||
| TPS Sensor | 1 | 1 | 1 | 1 | |
| RPM Sensor | 1 | 1 | 1 | 1 | |
| Speed Sensor | 1 | 1 | 1 | 1 | |
| Oil Temp Sensor | 1 | 1 | |||
| Low Range Sensor | 1 | 1 | |||
| Shifter Selection Switch | 1 | 1 | 1 | 1 | |
| Tuning Maps Selection Switch | 1 | 1 | 1 | 1 | |
| Tiptronic Up Switch | 1 | 1 | 1 | 1 | |
| Tiptronic Down Switch | 1 | 1 | 1 | 1 | |
| Battery Volts | 1 | 1 | 1 | 1 | |
| Power Management | 1 | 1 | 1 | 1 | |
| UART Comms Port | 1 | 1 | 1 | 1 | |
| Hardware Outputs | |||||
| Low Volt Negative Drivers | 8 | 8 | 8 | 8 | |
| Low Volt Positive Drivers | 8 | 8 | 8 | 8 | |
| GP Outputs | 2 | 2 | 2 | * | Note 1 |
| Speedo Output | 1 | 1 | 1 | ||
| Electronic Relay Output | 1 | 1 | 1 | 1 | |
| Relay Output | 1 | 1 | 1 | 1 | |
| Reverse lights Relay Output | 1 | 1 | 1 | 1 | |
| Starter Relay Output | 1 | 1 | 1 | 1 | |
| LED Output | 5 | 5 | 5 | 5 | |
| Power Management | 1 | 1 | 1 | 1 | |
| Features | |||||
| Tiptronic Function | 1 | 1 | 1 | 1 | Note 2 |
| Overdrive Function | 1 | 1 | Note 2 | ||
| 2nd Start Function | 1 | 1 | |||
| 4 Tuning Maps | 1 | 1 | 1 | 1 | |
| Individual Gear Shift Profiles | 1 | 1 | 1 | 1 | |
| Duty Cycle Control | 1 | 1 | 1 | 1 | |
| Speedo Calibration | 1 | 1 | 1 | ||
| Lockup Control | 1 | 1 | 1 | 1 | |
| Lockup Selectable per Gear | 1 | 1 | 1 | 1 | |
| Transfer Box Ratio Adjustments | 1 | 1 | |||
| Number of Gears Capable | 10 | 10 | 10 | 10 | |
| Epoxy filed | 1 | 1 | 1 | 1 | |
| Notes | |||||
| Note 1 – * All drivers that is not used by the firmware become GP outputs | |||||
| Note 2 – These drivers share the same input as Tiptronic buttons. | |||||
| NB! Some of the firmware may still be under development. This is merely indicating the capabilities of the different classes. Make sure if such firmware are available before buying or quoting your customers | |||||
Leave A Comment?
You must be logged in to post a comment.